QuickDraw™ 3D enables your computer to display three-dimensional graphics using applications designed to take advantage of QuickDraw 3D. It also provides a common file format, called QuickDraw 3D Metafile (or 3DMF for short), for exchanging 3D documents. QuickDraw 3D also provides acceleration services which support plug-and-play accelerator cards.
For computers running the Mac® OS, the following are required to install and run QuickDraw 3D:
• a PowerPC™ based computer with a minimum of 24 megabytes of memory (RAM)
• Mac OS System 7.1.2 or later
The latest version of QuickDraw 3D, along with software demos, QuickDraw 3D Metafiles, and additional information is available through the Internet at the following site:
http://www.apple.com/quicktime/
Troubleshooting
If you try to start an application that uses QuickDraw 3D and get the message “The application ‘<application name>’ could not be launched because QuickDraw 3D could not be found,” make sure that the following files are in the Extensions folder, inside the System Folder:
• QuickDraw™ 3D
• QuickDraw™ 3D IR
• QuickDraw™ 3D RAVE
• QuickDraw™ 3D Viewer
• QD3DCustomElements
How QuickDraw 3D uses memory
QuickDraw 3D is a shared library. When no applications that rely on QuickDraw 3D are open, the library does not take up memory space (RAM). Once a QuickDraw 3D-based application is open, the amount of memory taken up by the shared library doesn’t increase if other QuickDraw 3D-based applications are launched. Of course, each application will take up memory according to their size and the complexity of the files being used. The memory taken up by QuickDraw 3D becomes available when you quit all QuickDraw 3D-based applications.
While a QuickDraw 3D application is open, the QuickDraw 3D library allocates memory from “temporary memory.” This memory shows up in the “About This Computer…” window as memory used by the System. When you quit the application, the memory becomes available, but the size shown in the “About This Computer…” window may not reflect this. The memory previously used by QuickDraw 3D is, nonetheless, available for other applications (it is released to the applications as needed).
Apple QuickDraw 3D Accelerator Card
If you have an Apple QuickDraw 3D Accelerator Card present in your machine, the following files will also be installed in the Extensions folder, inside the System Folder:
• Apple QD3D HW Driver
• Apple QD3D HW Plug-In
If you need to re-install these files at a later time, you can do so by launching the Installer, as described in the section below under "If you need to reinstall QuickDraw 3D", selecting Custom Install from the pop-up menu, and then selecting the Apple QuickDraw 3D Accelerator Card item in the list.
We recommend that you turn off Virtual Memory when using Apple’s QuickDraw 3D Accelerator Card.
If you need to reinstall QuickDraw 3D
If you need to reinstall QuickDraw 3D, follow these steps:
1. Open the “QuickDraw™ 3D Install” folder and double-click the Installer icon.
2. After installing QuickDraw 3D, restart your computer.
Removing QuickDraw 3D
If you wish to remove QuickDraw 3D, follow these steps:
1. Open the “QuickDraw™ 3D Install” folder and double-click the Installer icon.
2. Choose Custom Remove from the pop-up menu.
3. Click the box next to each item to put a check in it.
Apple, the Apple logo, Macintosh, and Mac OS are trademarks of Apple Computer, Inc., registered in the U.S. and other countries. QuickDraw is a trademark of Apple Computer, Inc. All other product names are trademarks or registered trademarks of their respective holders. Mention of non-Apple products is for informational purposes and constitutes neither an endorsement nor a recommendation. Apple assumes no responsibility with regard to the selection, performance, or use of these products.
